请问为什么时间显示不正确，已按文档正确设置时区

caufrankie · 发表于 2020-6-7 23:02

已在void setup()中加入Blinker.setTimezone(8.0);设置时区为什么我的串口监视器和oled显示的时间都比正确时间晚8个小时

曾尝试把时区函数改成8以外的数据，不起作用
设备是ESP8266 nodemcu温湿度传感器 dht11 屏幕0.96OLED，目前程序能运行，屏幕显示预定的开机画面，进入后显示温湿度和时间日期界面，图像部分也能正常
[mw_shl_code=arduino,true]#define BLINKER_WIFI
#define BLINKER_MIOT_SENSOR
#include <Blinker.h>
#include <DHT.h>
#include <U8g2lib.h>

char auth[] = "*";
char ssid[] = "*";
char pswd[] = "*";

BlinkerNumber HUMI("humi");
BlinkerNumber TEMP("temp");

#define DHTPIN 2
#define DHTTYPE DHT11 // DHT 11
//#define DHTTYPE DHT22 // DHT 22  (AM2302), AM2321
//#define DHTTYPE DHT21 // DHT 21 (AM2301)

#define SCL  4                //GPIO14  D2
#define SDA  5                //GPIO12  D1
U8G2_SSD1306_128X64_NONAME_F_SW_I2C u8g2(U8G2_R0, SCL, SDA, U8X8_PIN_NONE); //scl,sda,rst

DHT dht(DHTPIN, DHTTYPE);

float humi_read = 0, temp_read = 0;

/*图像（一般以pb开头）、文字（一般以lb开头）数组*/

//开机时的图像: 88X50px length:550  sizeof:550B
const unsigned char pb_start[] U8X8_PROGMEM= {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,
0x00,0x00,0x00,0x00,0x80,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0xc0,0x01,0x00,0x00,
0x00,0x80,0x03,0x00,0xe0,0x00,0x00,0x00,0x00,0x80,0x0f,0x00,0xe0,0x00,0x00,0x00,
0x00,0x00,0x3e,0x00,0x70,0x00,0x00,0x00,0x00,0x00,0xfc,0x00,0x30,0x00,0x00,0x00,
0x00,0x00,0xf0,0x01,0x38,0x00,0x00,0x00,0x00,0x00,0xc0,0x07,0x1c,0x00,0x00,0x00,
0x00,0x00,0x00,0x1f,0x0e,0x00,0x00,0x00,0x80,0xff,0x7f,0xff,0xff,0xff,0x1f,0x00,
0x80,0xff,0xff,0xff,0xff,0xff,0x1f,0x00,0x80,0x01,0x00,0x00,0x00,0x00,0x18,0x00,
0x80,0x01,0x00,0x00,0x00,0x00,0x18,0x00,0x80,0x01,0x00,0x00,0x00,0x00,0x18,0x00,
0x80,0xf9,0xff,0xff,0xff,0xff,0x19,0x00,0x80,0xf9,0xff,0xff,0xff,0xff,0x19,0x00,
0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,
0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,
0x80,0x19,0x80,0x00,0x18,0x80,0x19,0x00,0x80,0x19,0xe0,0x01,0x78,0x80,0x19,0x00,
0x80,0x19,0xf8,0x00,0xf0,0x81,0x19,0x00,0x80,0x19,0x3e,0x00,0xc0,0x83,0x19,0x00,
0x80,0x19,0x0f,0x00,0x80,0x8f,0x19,0x00,0x80,0x19,0x02,0x00,0x00,0x8e,0x19,0x00,
0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,0x80,0x19,0x80,0x40,0x10,0x80,0x19,0x00,
0x80,0x19,0x80,0x61,0x38,0x80,0x19,0x00,0x80,0x19,0x80,0xe1,0x38,0x80,0x19,0x00,
0x80,0x19,0x80,0xf3,0x38,0x80,0x19,0x00,0x80,0x19,0x80,0xff,0x1f,0x80,0x19,0x00,
0x80,0x19,0x00,0xbf,0x0f,0x80,0x19,0x00,0x80,0x19,0x00,0x0c,0x03,0x80,0x19,0x00,
0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,0x80,0x19,0x00,0x00,0x00,0x80,0x19,0x00,
0x80,0x19,0x00,0x00,0x00,0xc0,0x19,0x00,0x80,0xf9,0xff,0xff,0xff,0xff,0x19,0x00,
0x80,0xf9,0xff,0xff,0xff,0xff,0x19,0x00,0x80,0x01,0x00,0x00,0x00,0x00,0x18,0x00,
0x80,0x01,0x00,0x00,0x00,0x00,0x18,0x00,0x80,0xff,0xff,0xff,0xff,0xff,0x1f,0x00,
0x80,0xff,0xff,0xff,0xff,0xff,0x1f,0x00,0x00,0x7f,0x5f,0xff,0xff,0xe7,0x0f,0x00,
0x00,0x60,0x0c,0x00,0x00,0xc6,0x00,0x00,0x00,0xe0,0x0f,0x00,0x00,0x7e,0x00,0x00,
0x00,0xc0,0x07,0x00,0x00,0x7c,0x00,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};

// width: 107, height: 55
const unsigned char col2[] U8X8_PROGMEM = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0x00,0xc0,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x70,0x00,0x00,0x80,0x07,0x00,0x00,0x00,0x00,0xc0,0xff,0xff,0x07,0x00,0x70,0x00,0x00,0x00,0x0f,0x00,0x00,0x00,0x00,0xc0,0xff,0xff,0x07,0x00,0x30,0x00,0xc0,0xff,0xff,0x1f,0x00,0x00,0x00,0x40,0x80,0x03,0x04,0x00,0x30,0x00,0xc0,0xff,0xff,0x1f,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x30,0x00,0xc0,0x00,0x00,0x1c,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x30,0x00,0xc0,0x00,0x00,0x1c,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x60,0x30,0x18,0xc0,0x00,0x00,0x1c,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0xe0,0x30,0x1c,0xc0,0xfe,0xff,0x1f,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x60,0x30,0x38,0x00,0xfe,0xff,0x03,0x00,0x00,0x00,0x00,0x80,0x03,0x00,0x70,0x30,0x38,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x80,0xff,0xff,0x03,0x70,0x30,0x70,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x80,0xff,0xff,0x03,0x70,0x30,0x70,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x38,0x30,0xe0,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x38,0x30,0xe0,0x00,0xfc,0xff,0x01,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x18,0x30,0xc0,0x01,0xfc,0xff,0x01,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x1c,0x30,0xc0,0x01,0x00,0x47,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x0c,0x30,0x80,0x01,0x00,0xe7,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x0e,0x30,0x80,0x01,0x00,0xe7,0x01,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x06,0x30,0x00,0x00,0x00,0xc7,0x03,0x00,0x00,0x00,0x60,0x80,0x03,0x18,0x00,0x30,0x00,0x00,0x00,0x87,0x01,0x00,0x00,0x00,0xe0,0xff,0xff,0x1f,0x00,0x30,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0xe0,0xff,0xff,0x1f,0x00,0x3f,0x00,0xe0,0xff,0xff,0x3f,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3e,0x00,0xe0,0xff,0xff,0x3f,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1e,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 };
// width: 48, height: 56
const unsigned char col[] U8X8_PROGMEM = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x04,0x00,
0x00,0x38,0x00,0x00,0x9c,0x7f,0xe0,0xff,0x07,0x00,0xb8,0x60,0x20,0x00,0x00,0x00,
0x80,0x60,0x20,0xcc,0x00,0x00,0x82,0x7f,0x20,0xc4,0x00,0x00,0x8e,0x60,0xa0,0xff,
0x07,0x03,0x98,0x7f,0x20,0xc4,0x00,0x03,0x00,0x00,0x20,0xfc,0x00,0x03,0x00,0x00,
0x20,0x00,0x00,0x00,0xd8,0xff,0x20,0xff,0x01,0x00,0x58,0xda,0x20,0xcc,0x00,0x03,
0x4c,0xda,0x30,0x7c,0x00,0x03,0x4c,0xda,0x30,0x78,0x00,0x03,0xe6,0xdf,0x18,0xfc,
0x00,0x00,0xf6,0xff,0xc1,0x87,0x07,0x00,0x02,0x00,0x80,0x01,0x04,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x08,0x00,0x00,0xcc,0xff,
0x00,0x38,0x00,0x00,0xd8,0x40,0xe0,0xff,0x07,0x00,0xd0,0x40,0x20,0x00,0x00,0x00,
0xc2,0x7f,0x20,0xcc,0x00,0x00,0xce,0x40,0x20,0xc4,0x00,0x00,0xdc,0x40,0xa0,0xff,
0x07,0x03,0xc8,0xff,0x20,0xc4,0x00,0x03,0x00,0x1a,0x20,0xfc,0x00,0x03,0x48,0xd2,
0x20,0x00,0x00,0x00,0x48,0xd2,0x20,0xff,0x01,0x00,0xc8,0x53,0x20,0xcc,0x00,0x03,
0x8c,0x73,0x30,0x7c,0x00,0x03,0x8c,0x33,0x30,0x78,0x00,0x03,0x04,0x1f,0x18,0xfc,
0x00,0x00,0xe6,0xff,0xc1,0x87,0x07,0x00,0x04,0x00,0x80,0x01,0x04,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00
};

// width: 28, height: 27
const unsigned char col3[] U8X8_PROGMEM = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1c,0x3c,0x00,0x00,0x32,0xff,0x00,0x00,
0x22,0xc3,0x00,0x00,0xb2,0xc1,0x00,0x00,0x9c,0x01,0x00,0x00,0x80,0x01,0x00,0x00,
0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x81,0x00,0x00,
0x00,0xc3,0x00,0x00,0x00,0xff,0x00,0x00,0x00,0x3c,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 };

void dis_Time(){
  //Blinker.setTimezone(8.0);

  char str_week[]="";
  char str_date[]="";
  char str_big_Time[]="";
  char str_small_second[]="";
  int num_temp=0;
  char str_temp[6];

  if(Blinker.second()>=0){
do {
   u8g2.clearBuffer();
   num_temp=Blinker.year()%100;
   if(num_temp<10){
      strcat(str_date,"0");
   }
   itoa(num_temp,str_temp,10); //日期
   strcat(str_date,str_temp);
   num_temp=Blinker.month();
   itoa(num_temp,str_temp,10);
   strcat(str_date,"-");
   if(Blinker.month()<10){
      strcat(str_date,"0");
   }
   strcat(str_date,str_temp);
   num_temp=Blinker.mday();
   itoa(num_temp,str_temp,10);
   strcat(str_date,"-");
   strcat(str_date,str_temp);
   num_temp=Blinker.wday();
   char* week_str[8]={"日","一","二","三","四","五","六","日"};
   strcat(str_date,"星期");
   strcat(str_date,week_str[Blinker.wday()]);
   Serial.print("日期:");
   Serial.print(str_date);
   u8g2.setFont(u8g2_font_wqy12_t_gb2312a); // 汉字 14*26
   u8g2.setCursor(25, 54);
   u8g2.print(str_date);
   num_temp=Blinker.wday();
   itoa(num_temp,str_temp,10); //星期
   strcat(str_week,str_temp);
   num_temp=Blinker.hour();
   itoa(num_temp,str_temp,10); //时分
   if(Blinker.hour()<10){
      strcat(str_big_Time,"0");
   }
   strcat(str_big_Time,str_temp);
   num_temp=Blinker.minute();
   itoa(num_temp,str_temp,10);
   strcat(str_big_Time,":");
   if(Blinker.minute()<10){
      strcat(str_big_Time,"0");
   }
   strcat(str_big_Time,str_temp);
   Serial.print("时分:");
   Serial.print(str_big_Time);
   u8g2.setFont(u8g2_font_logisoso28_tf ); // 大字 14*26
   u8g2.setCursor(20, 34);
   u8g2.print(str_big_Time);
   num_temp=Blinker.second();
   itoa(num_temp,str_temp,10); //秒
   if(Blinker.second()<10){
      strcat(str_small_second,"0");
   }
   strcat(str_small_second,str_temp);
   Serial.print("秒:");
   Serial.println(str_small_second);

   } while ( u8g2.nextPage() );
  }
}

void heartbeat()
{
HUMI.print(humi_read);
TEMP.print(temp_read);
}

void dataStorage()
{
Blinker.dataStorage("temp", temp_read);
Blinker.dataStorage("humi", humi_read);

}

void miotQuery(int32_t queryCode)    //小爱同学控制
{
BLINKER_LOG("MIOT Query codes: ", queryCode);

         int humi_read_int=humi_read;    //去掉湿度浮点
         BlinkerMIOT.temp(temp_read);
         BlinkerMIOT.humi(humi_read_int);
         BlinkerMIOT.print();

}

void dataRead(const String & data)
{
BLINKER_LOG("Blinker readString: ", data);

Blinker.vibrate();

uint32_t BlinkerTime = millis();

Blinker.print("millis", BlinkerTime);
}
void setup()
{
Serial.begin(115200);
BLINKER_DEBUG.stream(Serial);
BLINKER_DEBUG.debugAll();
pinMode(LED_BUILTIN, OUTPUT);
digitalWrite(LED_BUILTIN, LOW);

Blinker.begin(auth, ssid, pswd);
Blinker.attachHeartbeat(heartbeat);
BlinkerMIOT.attachQuery(miotQuery);
Blinker.attachDataStorage(dataStorage);
dht.begin();

int humi_read_int=humi_read;
int temp_read_int=temp_read;
u8g2.begin();
u8g2.enableUTF8Print();
u8g2.clearBuffer();
u8g2.drawXBMP(34,5,60,54,pb_start);
u8g2.sendBuffer();
Blinker.delay(2000);

u8g2.clearBuffer();
u8g2.drawXBMP(10,5,107,55,col2);
u8g2.sendBuffer();
Blinker.delay(2000);

Blinker.setTimezone(8.0);

}

void loop()
{
Blinker.run();

float h = dht.readHumidity();
float t = dht.readTemperature();

if (isnan(h) || isnan(t))
{
      BLINKER_LOG("Failed to read from DHT sensor!");
}
else
{
      BLINKER_LOG("Humidity: ", h, " %");
      BLINKER_LOG("Temperature: ", t, " *C");
      humi_read = h;
      temp_read = t;
}

u8g2.clearBuffer();
//u8g2.setFont(u8g2_font_unifont_t_chinese2);
u8g2.setFont(u8g2_font_ncenB14_tr);
u8g2.drawXBM(1, 5, 45, 54, col);
//u8g2.drawXBM(80, 16,16, 24, bitmap3);
u8g2.setCursor(46, 25);
u8g2.print(temp_read);
u8g2.setCursor(46, 57);
u8g2.print(humi_read);
//u8g2.setCursor(103, 23);
u8g2.drawXBM(100, 5, 28, 27, col3);
u8g2.setCursor(103, 55);
u8g2.print("%");
u8g2.sendBuffer();
Blinker.delay(4000);

dis_Time();
Blinker.delay(4000);

//u8g2.setCursor(5, 15);
// u8g2.print("温度:");
//u8g2.setCursor(70, 14);
//u8g2.print(temp_read);
// u8g2.setCursor(5, 47);
//u8g2.print("湿度:");
// u8g2.setCursor(70, 47);
// u8g2.print(humi_read);
//u8g2.sendBuffer();

}[/mw_shl_code]

奈何col · 发表于 2020-6-8 00:26

8266 package 2.7.1修改了时区
请更新blinker lib dev3.0分支

caufrankie · 发表于 2020-6-8 09:08

奈何col 发表于 2020-6-8 00:26
8266 package 2.7.1修改了时区
请更新blinker lib dev3.0分支

感谢解答！已更新blinker lib dev 3.0,现在时间正常了，调整时区参数，时间会跟着变化，但不知什么原因日期有问题，比如现在是北京时间8日早上8点，我调整Blinker.setTimezone(-8.0);，程序输出的时间是6月8日16点对比网上查询的时区时间UTC-8：2020-6-7 16:58:15，日期不会跟随时区变化，是什么原因？再次感谢

三水 · 发表于 2020-6-8 11:52

caufrankie 发表于 2020-6-8 09:08
感谢解答！已更新blinker lib dev 3.0,现在时间正常了，调整时区参数，时间会跟着变化，但不知什么原因日 ...

已更新库时间相关函数更新dev3.0库测试

caufrankie · 发表于 2020-6-8 19:54

三水发表于 2020-6-8 11:52
已更新库时间相关函数更新dev3.0库测试

就是已经更新了，时区函数已经生效了

三水 · 发表于 2020-6-9 20:02

caufrankie 发表于 2020-6-8 19:54
就是已经更新了，时区函数已经生效了

我的意思是叫你再更新一遍

caufrankie · 发表于 2020-6-10 08:23

三水发表于 2020-6-9 20:02
我的意思是叫你再更新一遍

谢谢回复，是要重新下载dev3.0放到库文件夹么，原来的点灯master那个是删除还是保留？经过两天观察hour和分钟是正常了日期是咱们正常时间的早上8点才跳转的新的正确日期，比北京标准时间晚了8小时

caufrankie · 发表于 2020-6-11 09:35

基本正常了，分享下处理过程。主要原因是BLINKER更新了8266新版2.71库，blinker更新了dev3.0，Arduino IDE 在更新中出现问题，最终删除这些文件，重新下载安装，时区函数生效，日期问题正常。旧的8266的package找到Arduino15目录删除即可，具体办法奈何大佬的帖子里有讲，论坛搜索吧，结贴！

		自动登录	找回密码
密码			立即注册

[已解答] 请问为什么时间显示不正确，已按文档正确设置时区