blinker控制RGB LED示例

coloz

这是一个RGB控制示例，帮助大家更好的编写灯控程序。

注意：只有changeLight()函数在改变灯的状态，如果你是用的其他灯，只用在setup中进行初始化，在changeLight中改变灯的状态即可。

[mw_shl_code=arduino,true]

#define BLINKER_WIFI

#include <Blinker.h>

char auth[] = "xxxxxxxxxxx";
char ssid[] = "xxxxx";
char pswd[] = "xxxxxxxxxx";

#define RGB_1 "RGBKey"

BlinkerRGB RGB1(RGB_1);

bool switch_state = false;

int red=0;
int green=0;
int blue=0;
int bright=0;

void rgb1_callback(uint8_t r_value, uint8_t g_value, uint8_t b_value, uint8_t bright_value)
{
    digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));
    red=r_value;
    green=g_value;
    blue=b_value;
    bright=bright_value;
    changeLight();
    BLINKER_LOG("R value: ", r_value);
    BLINKER_LOG("G value: ", g_value);
    BLINKER_LOG("B value: ", b_value);
    BLINKER_LOG("Rrightness value: ", bright_value);
    RGB1.brightness(bright);
    RGB1.print(red, green, blue);
}

void switch_callback(const String & state)
{
    BLINKER_LOG("get switch state: ", state);

    if (state == BLINKER_CMD_ON) {
        switch_state = true;
        bright=255;
        changeLight();
        BUILTIN_SWITCH.print("on");
    }
    else if (state == BLINKER_CMD_OFF) {
        switch_state = false;
        bright=0;
        changeLight();
        digitalWrite(LED_BUILTIN, LOW);

        BUILTIN_SWITCH.print("off");
    }
}

void heartbeat()
{
    if (switch_state) BUILTIN_SWITCH.print("on");
    else BUILTIN_SWITCH.print("off");
    RGB1.brightness(bright);
    RGB1.print(red, green, blue);
}


void dataRead(const String & data)
{
    BLINKER_LOG("Blinker readString: ", data);   
    uint32_t BlinkerTime = millis();   
    Blinker.print("millis", BlinkerTime);
}

void changeLight(){
    int red_temp=map(red*bright/255,0,255,1023,0);
    int green_temp= map(green*bright/255,0,255,1023,0);
    int blue_temp= map(blue*bright/255,0,255,1023,0);
    BLINKER_LOG("red_temp: ", red_temp);
    BLINKER_LOG("green_temp: ", green_temp);
    BLINKER_LOG("blue_temp: ", blue_temp);
    analogWrite(D8,red_temp);
    analogWrite(D9,green_temp);
    analogWrite(D10,blue_temp);
}

void setup()
{
    Serial.begin(115200);
    BLINKER_DEBUG.stream(Serial);

    pinMode(LED_BUILTIN, OUTPUT);
    digitalWrite(LED_BUILTIN, LOW);

    Blinker.begin(auth, ssid, pswd);
    Blinker.attachData(dataRead);
    Blinker.attachHeartbeat(heartbeat);
    BUILTIN_SWITCH.attach(switch_callback);
   
    RGB1.attach(rgb1_callback);
}

void loop()
{
    Blinker.run();
}[/mw_shl_code]

寝室咯

可以分享一下blinker软件中界面的设置吗？谢谢啦

coloz

寝室咯 发表于 2019-9-12 09:58
可以分享一下blinker软件中界面的设置吗？谢谢啦

就是一个颜色拾取组件，没了，不过这个程序是2.2.7使用的，不知道2.2.6正常不

carlbeven

coloz老师，能否写一个教程？开关按键：RGB循环变颜色的；颜色拾取：使用拾色按键选取颜色，调节亮度并且保持该颜色、亮度。折腾了许久不懂如何中断RGB循环颜色和解决blinker app端接受数据延迟的问题。谢谢~

coloz

carlbeven 发表于 2019-9-18 19:55
coloz老师，能否写一个教程？开关按键：RGB循环变颜色的；颜色拾取：使用拾色按键选取颜色，调节亮度并且保 ...

https://github.com/blinker-iot/Blinker_PRO_SMART_LAMP