接上一篇帖子【新提醒】【KittenBot巡线小车试用】上电初体验-Arduino中文社区 - Powered by Discuz! http://www.arduino.cn/thread-49513-1-1.html
看来必须使用Kittenblock，之前无线模块的拨码拨到了特殊模式，连上usb，蜂蜜器响，选择串口后就选择了，点击arduino，发现返回如下，这时发现小车电源开关没开，无线模块发烫厉害
开电源开关，蜂蜜器不响了，再烧录，报错，如此3、4次，一直报错，无线模块发烫厉害。且烧录完，串口丢失，难道又要重启软件选择串口？串口输出的信息是什么意思？
软件报错信息输出如下:
avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x4c avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x4c
打开开关时，就会出现 avrdude done. Thank you.但是还是下载失败啊，整个电脑都累了，其他程序就QQ、浏览器
虽然该开发环境免安装，但是建议再优化一下， 1、增加字体大小设置 2、增加下载进度提示，比如arduino IDE会显示upload ing... 3、既然Kittenblock本身内置了Arduino 1.68和机器人相关的大多数库，为什么开发环境无法选择源文件或者例程？arduino里面不是有很多example 同时使用USB电源和电池电源对小车会不会有影响？这时小车开关如果关闭，电池处于充电状态还是？怎么看到电充满了？ 为什么无线模块一接USB电源就发烫厉害
还有按照你们的例程我没有下载固件成功，小车出厂固件是哪个版本?无线是哪个版本？ 由于我上电前无线拨码置于特殊模式，是不是更新WIFI模块自身的固件？可是我没联网啊，它怎么更新？那现在还是原来的固件？可是和我手机一直没连上
| 
发表于 2017-9-27 22:10
楼主