求助，板子上传失败！

张阳一鸟

是不是板子的型号不对？


Arduino:1.6.8 (Windows 10), 开发板："Arduino/Genuino Uno"


构建选项已变更，全部重新构建


项目使用了 1,066 字节，占用了 (3%) 程序存储空间。最大为 32,256 字节。
全局变量使用了9字节，(0%)的动态内存，余留2,039字节局部变量。最大为2,048字节。
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x38
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x38
上传出错。查看页面 http://www.arduino.cc/en/Guide/Troubleshooting#upload 获取建议。


在文件 -> 首选项开启
“编译过程中显示详细输出”选项
这份报告会包含更多信息。

XIOAMING

我这里也是同样的问题，不知道怎么解决=-=

杨蒙

构建选项已变更，全部重新构建
项目使用了 15698 字节，占用了 (6%) 程序存储空间。最大为 253952 字节。
全局变量使用了758字节，(9%)的动态内存，余留7434字节局部变量。最大为8192字节。
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer
上传项目出错

sun910231

如驱动已经安装板子正常：检查1，板子的端口选择是不是正确；2，0&1 IO上有没有连东西；

mailjmq

串口没选对

Arduino_xyz

什么上传失败，会让你觉得连1根线都在欺负你？


什么上传失败，会让你觉得防不胜防？


什么上传失败，说明你想用手机控制arduino？