GP2Y0E03烧写熔丝位失败

shy0511 · 发表于 2021-10-20 19:25

想用arduino uno烧写GP2Y0E03，改写IIC地址，但是一直不成功

/*
----------------------------------------------
Title: E_FUSE.ino
Author: Martin Pålsson
Description:
E-Fuse programmer for SHARP GP2Y0E02B, GP2Y0E03
-----------------------------------------------
*/
#include <Wire.h>
/* Default address of sensor */
#define ADDRESS (0x80 >> 1) // 7 MSB, default address of sensor
/* Desired address of the sensor */
#define SETADDR 0x00 // 4 MSB, will bitshift when used.
/* Prototypes */
int ScanBus();
uint8_t readSequence1(uint8_t devAddr, uint8_t regAddr);
void writeSequence(uint8_t devAddr, uint8_t regAddr, uint8_t data);
void EFuseSlaveID(uint8_t newID);
/* Global variables */
//uint8_t checkSum = 0; // Not currently used
void setup()
{
pinMode(4, OUTPUT); // Connect to Vpp pad on sensor
pinMode(13, OUTPUT); // Onboard LED
digitalWrite(13, HIGH); // To indicate that serial communication has been established. No led - Connection to PC established.
Wire.begin();
Serial.begin(9600);
while (!Serial); // Due: wait for serial monitor
digitalWrite(13, LOW); // To acknowledge that serial communication has been established.
Serial.println("\nGP2Y0E02B E-Fuse Programmer Version 1.0");
}
void loop()
{
Serial.println("Scanning I2C bus...");
if(ScanBus())
{
EFuseSlaveID(byte(SETADDR));
}
else
{
Serial.println("No devices found on bus");
}
/* Nothing else to do */
while(1);;
}
void EFuseSlaveID(uint8_t newID)
{
/* ----- Stage 1 ----- */
Serial.println("Stage 1 started.");
writeSequence(byte(ADDRESS), byte(0xEC), byte(0xFF));
Serial.println("Data = 0xFF is set in Address = 0xEC");
digitalWrite(4, HIGH);
Serial.println("3.3V is applied in the Vpp terminal");
/* ----- Stage 2 ------ */
Serial.println("Stage 2 started.");
writeSequence(byte(ADDRESS), byte(0xC8), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xC8");
/* ----- Stage 3 ------ */
Serial.println("Stage 3 started.");
writeSequence(byte(ADDRESS), byte(0xC9), byte(0x45));
Serial.println("Data = 0x45 is set in Address = 0xC9");
/* ----- Stage 4 ------ */
/* THIS IS WHERE THE ADDRESS WILL BE SET! */
Serial.println("Stage 4 started.");
writeSequence(byte(ADDRESS), byte(0xCD), byte(newID >> 4));
Serial.println("Data = SETADDR >> 4 is set in Address = 0xCD");
/* ----- Stage 5 ------ */
Serial.println("Stage 5 started.");
writeSequence(byte(ADDRESS), byte(0xCA), byte(0x01));
Serial.println("Data = 0x01 is set in Address = 0xCA");
Serial.println("Wait for 500 us");
delayMicroseconds(500);
/* ----- Stage 6 ------ */
Serial.println("Stage 6 started.");
writeSequence(byte(ADDRESS), byte(0xCA), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xCA");
digitalWrite(4, LOW);
Serial.println("Vpp terminal grounded.");
/* ----- Stage 7 ------ */
Serial.println("Stage 7 started.");
writeSequence(byte(ADDRESS), byte(0xEF), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xEF");
writeSequence(byte(ADDRESS), byte(0xC8), byte(0x40));
Serial.println("Data = 0x40 is set in Address = 0xC8");
writeSequence(byte(ADDRESS), byte(0xC8), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xC8");
/* ----- Stage 8 ------ */
Serial.println("Stage 8 started.");
writeSequence(byte(ADDRESS), byte(0xEE), byte(0x06));
Serial.println("Data = 0x06 is set in Address = 0xEE");
/* ----- Stage 9 ------ */
Serial.println("Stage 9 started.");
writeSequence(byte(ADDRESS), byte(0xEF), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xEF");
writeSequence(byte(ADDRESS), byte(0xEC), byte(0xFF));
Serial.println("Data = 0xFF is set in Address = 0xEC");
writeSequence(byte(ADDRESS), byte(0xEF), byte(0x03));
Serial.println("Data = 0x03 is set in Address = 0xEF");
Serial.println("Read out the data in Address = 0x27.");
Serial.print("Data: 0B");
Serial.println(readSequence1(byte(ADDRESS), byte(0x27)), BIN);
writeSequence(byte(ADDRESS), byte(0xEF), byte(0x00));
Serial.println("Data = 0x00 is set in Address = 0xEF");
writeSequence(byte(ADDRESS), byte(0xEC), byte(0x7F));
Serial.println("Data = 0x7F is set in Address = 0xEC");
}
void writeSequence(uint8_t devAddr, uint8_t regAddr, uint8_t data)
{
Wire.beginTransmission(devAddr);
Wire.write(byte(regAddr));
Wire.write(data);
Wire.endTransmission();
}
uint8_t readSequence1(uint8_t devAddr, uint8_t regAddr)
{
Wire.beginTransmission(devAddr);
Wire.write(byte(regAddr));
Wire.endTransmission();
Wire.requestFrom(devAddr, 1);
return Wire.read();
}
int ScanBus()
{
byte error, address;
int nDevices;
//Serial.println("I2C Scanner starting...");
nDevices = 0;
for(address = 0; address < 127; address++ )
{
// The i2c_scanner uses the return value of
// the Write.endTransmisstion to see if
// a device did acknowledge to the address.
Wire.beginTransmission(address);
error = Wire.endTransmission();
if (error == 0)
{
Serial.print("I2C device found at address 0x");
if (address<16)
Serial.print("0");
Serial.print(address << 1,HEX);
Serial.println(" !");
nDevices++;
}
else if (error==4)
{
Serial.print("Unknown error at address 0x");
if (address<16)
Serial.print("0");
Serial.println(address,HEX);
}
}
if (nDevices == 0)
{
Serial.println("No I2C devices found\n");
return 0;
}
else
{
Serial.print(nDevices);
Serial.println(" devices found.");
Serial.println("I2C Scanner done.\n");
return nDevices;
}
}

复制代码

		自动登录	找回密码
密码			立即注册

[未解决] GP2Y0E03烧写熔丝位失败