一直编译错误不知道什么原因

m1onster

#include <Blinker.h>
#include <DHT.h>
#define BLINKER_WIFI
#define led 5
#define DHTPIN 13
#define DHTTYPE DHT22   // DHT 22  (AM2302), AM2321


char auth[] = "097e814d5354";
char ssid[] = "young";
char pswd[] = "qweasdzxc";

BlinkerNumber HUMI("humi");
BlinkerNumber TEMP("temp");
BlinkerButton Button1("btn-abc");
BlinkerButton Button2("one");
// Download Adafruit DHT-sensor-library library here:
// https://github.com/adafruit/DHT-sensor-library



DHT dht(DHTPIN, DHTTYPE);

uint32_t read_time = 0;

float humi_read, temp_read;



// 按下按键即会执行该函数
void button1_callback(const String & state) {
    BLINKER_LOG("get button state: ", state);
    if (state=="on")
    {
        digitalWrite(LED_BUILTIN, LOW);
        // 反馈开关状态
        Button1.print("on");
    }
    else if(state=="off")
    {
        digitalWrite(LED_BUILTIN, HIGH);
        // 反馈开关状态
        Button1.print("off");
    }
    BlinkerButton Button1("btn-abc");

// 按下按键即会执行该函数
void button2_callback(const String & state) {
    BLINKER_LOG("get button state: ", state);
    if (state=="on")
    {
        digitalWrite(led, HIGH);
        // 反馈开关状态
        Button2.print("on");
    }
    else if(state=="off")
    {
        digitalWrite(led, LOW);
        // 反馈开关状态
        Button2.print("off");
    }

void heartbeat()
{
    HUMI.print(humi_read);
    TEMP.print(temp_read);

}

void setup()
{
    Serial.begin(115200);
    BLINKER_DEBUG.stream(Serial);

    pinMode(LED_BUILTIN, OUTPUT);
    digitalWrite(LED_BUILTIN, HIGH);
    pinMode(led, OUTPUT);
    digitalWrite(led, LOW);

    Blinker.begin(auth, ssid, pswd);
    Blinker.attachHeartbeat(heartbeat);
    Button1.attach(button1_callback);
    Button2.attach(button2_callback);
    dht.begin();
}

void loop()
{
    Blinker.run();

    if (read_time == 0 || (millis() - read_time) >= 2000)
    {
        read_time = millis();

        float h = dht.readHumidity();
        float t = dht.readTemperature();        

        if (isnan(h) || isnan(t)) {
            BLINKER_LOG("Failed to read from DHT sensor!");
            return;
        }

        float hic = dht.computeHeatIndex(t, h, false);

        humi_read = h;
        temp_read = t;

        BLINKER_LOG("Humidity: ", h, " %");
        BLINKER_LOG("Temperature: ", t, " *C");
        BLINKER_LOG("Heat index: ", hic, " *C");
    }
}



错误信息
Arduino:1.8.13 (Windows 10), 开发板："Generic ESP8266 Module, 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), dtr (aka nodemcu), 26 MHz, 40MHz, DOUT (compatible), 1MB (FS:64KB OTA:~470KB), 2, nonos-sdk 2.2.1+100 (190703), v2 Lower Memory, Disabled, None, Only Sketch, 115200"

In file included from C:\Users\admin\Desktop\Hello_WiFi\_____\_____.ino:47:0:

C:\Users\admin\Documents\Arduino\libraries\Blinker\src/Blinker.h:215:6: error: #error Please set a mode BLINKER_BLE/BLINKER_WIFI/BLINKER_MQTT ! Please check your mode setting.

     #error Please set a mode BLINKER_BLE/BLINKER_WIFI/BLINKER_MQTT ! Please check your mode setting.

      ^

"Blinker.h" 对应多个库

已使用： C:\Users\admin\Documents\Arduino\libraries\Blinker

未使用：C:\Users\admin\Documents\Arduino\libraries\blinker-library-master

exit status 1

为开发板 Generic ESP8266 Module 编译时出错。



在文件 -> 首选项开启
“编译过程中显示详细输出”选项
这份报告会包含更多信息。



超级奇怪不知道怎么回事

奈何col

#define BLINKER_WIFI 要放在最前面

m1onster

奈何col 发表于 2020-12-29 08:59
#define BLINKER_WIFI 要放在最前面

谢谢已经成功解决

m1onster

奈何col 发表于 2020-12-29 08:59
#define BLINKER_WIFI 要放在最前面

还有一个问题就是数据键有数据可是图表没数据是什么原因