Arduino:1.8.12 (Windows 10), 开发板："Generic ESP8266 Module, 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), dtr (aka nodemcu), 26 MHz, 40MHz, DOUT (compatible), 1MB (FS:none OTA:~502KB), 2, nonos-sdk 2.2.1+100 (190703), v2 Lower Memory, Disabled, None, Only Sketch, 115200"
In file included from D:\MIOT_LIGHT_0426_EFF\MIOT_LIGHT_0426_EFF.ino:15:0:
C:\Users\Adminis\Documents\Arduino\libraries\FastLED/FastLED.h:14:21: note: #pragma message: FastLED version 3.003.003
# pragma message "FastLED version 3.003.003"
^
In file included from C:\Users\Adminis\Documents\Arduino\libraries\FastLED/FastLED.h:65:0,
from D:\MIOT_LIGHT_0426_EFF\MIOT_LIGHT_0426_EFF.ino:15:
C:\Users\Adminis\Documents\Arduino\libraries\FastLED/fastspi.h:130:23: note: #pragma message: No hardware SPI pins defined. All SPI access will default to bitbanged output
# pragma message "No hardware SPI pins defined. All SPI access will default to bitbanged output"
^
Executable segment sizes:
IROM : 507068 - code in flash (default or ICACHE_FLASH_ATTR)
IRAM : 28760 / 32768 - code in IRAM (ICACHE_RAM_ATTR, ISRs...)
DATA : 1476 ) - initialized variables (global, static) in RAM/HEAP
RODATA : 6024 ) / 81920 - constants (global, static) in RAM/HEAP
BSS : 30368 ) - zeroed variables (global, static) in RAM/HEAP
项目使用了 543328 字节，占用了 (53%) 程序存储空间。最大为 1023984 字节。
全局变量使用了37868字节，(46%)的动态内存，余留44052字节局部变量。最大为81920字节。
esptool.py v2.8
Serial port COM4
Connecting....
Chip is ESP8266EX
Features: WiFi
Crystal is 26MHz
MAC: 18:fe:34:00:00:00
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Auto-detected Flash size: 1MB
Compressed 547488 bytes to 388983...
Writing at 0x00000000... (4 %)Traceback (most recent call last):
File "C:\Users\Adminis\AppData\Local\Arduino15\packages\esp8266\hardware\esp8266\2.7.1/tools/upload.py", line 65, in <module>
esptool.main(cmdline)
File "C:/Users/Adminis/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.7.1/tools/esptool\esptool.py", line 2938, in main
operation_func(esp, args)
File "C:/Users/Adminis/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.7.1/tools/esptool\esptool.py", line 2374, in write_flash
esp.flash_defl_block(block, seq, timeout=DEFAULT_TIMEOUT * ratio * 2)
File "C:/Users/Adminis/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.7.1/tools/esptool\esptool.py", line 104, in inner
return func(*args, **kwargs)
File "C:/Users/Adminis/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.7.1/tools/esptool\esptool.py", line 672, in flash_defl_block
self.ESP_FLASH_DEFL_DATA, struct.pack('<IIII', len(data), seq, 0, 0) + data, self.checksum(data), timeout=timeout)
File "C:/Users/Adminis/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.7.1/tools/esptool\esptool.py", line 379, in check_command
raise FatalError.WithResult('Failed to %s' % op_description, status_bytes)
esptool.FatalError: Failed to write compressed data to flash after seq 0 (result was C100)
esptool.FatalError: Failed to write compressed data to flash after seq 0 (result was C100)
在文件 -> 首选项开启
“编译过程中显示详细输出”选项
这份报告会包含更多信息。
|
发表于 2020-5-31 15:39