|
|
麻烦大佬帮忙看看这个报错嘛。
前两天写好了程序，传到板子上，可以正常跑起来，结果第二天睡醒就不行了；
现在连USB后，8266下面一直在发热，但是设备管理器可以识别出；
Arduino:1.8.12 (Windows 10), 开发板："NodeMCU 1.0 (ESP-12E Module), 80 MHz, Flash, Legacy (new can return nullptr), All SSL ciphers (most compatible), 4MB (FS:2MB OTA:~1019KB), 2, v2 Lower Memory, Disabled, None, Only Sketch, 115200"
Executable segment sizes:
IROM : 438940 - code in flash (default or ICACHE_FLASH_ATTR)
IRAM : 28312 / 32768 - code in IRAM (ICACHE_RAM_ATTR, ISRs...)
DATA : 1364 ) - initialized variables (global, static) in RAM/HEAP
RODATA : 5220 ) / 81920 - constants (global, static) in RAM/HEAP
BSS : 30208 ) - zeroed variables (global, static) in RAM/HEAP
项目使用了 473836 字节，占用了 (45%) 程序存储空间。最大为 1044464 字节。
全局变量使用了36792字节，(44%)的动态内存，余留45128字节局部变量。最大为81920字节。
esptool.py v2.8
Serial port COM4
Connecting........_
Chip is ESP8266EX
Features: WiFi
Crystal is 26MHz
MAC: f4:cf:a2:4c:af:aa
Uploading stub...
Running stub...
Stub running...
Configuring flash size...
Traceback (most recent call last):
File "C:\Users\mumu_\AppData\Local\Arduino15\packages\esp8266\hardware\esp8266\2.6.3/tools/upload.py", line 65, in <module>
esptool.main(cmdline)
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 2933, in main
detect_flash_size(esp, args)
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 2241, in detect_flash_size
flash_id = esp.flash_id()
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 607, in flash_id
return self.run_spiflash_command(SPIFLASH_RDID, b"", 24)
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 853, in run_spiflash_command
old_spi_usr = self.read_reg(SPI_USR_REG)
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 490, in read_reg
val, data = self.command(self.ESP_READ_REG, struct.pack('<I', addr))
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 347, in command
p = self.read()
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 292, in read
return next(self._slip_reader)
File "C:/Users/mumu_/AppData/Local/Arduino15/packages/esp8266/hardware/esp8266/2.6.3/tools/esptool\esptool.py", line 2045, in slip_reader
raise FatalError("Timed out waiting for packet %s" % waiting_for)
esptool.FatalError: Timed out waiting for packet header
esptool.FatalError: Timed out waiting for packet header
|
|
发表于 2020-4-7 11:17