at20温湿度+bmp280气压+4个AI输入+1个DO+1个DO延时超精简程序
#define BLINKER_WIFI#include <Blinker.h>
#include <Arduino.h>
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_BMP280.h>
#include <SparkFun_Qwiic_Humidity_AHT20.h>
#define BUTTON_1 "btn-abc"
#define BUTTON_2 "btn-123"
#define LED_BUILTIN1 4
#define LED_BUILTIN2 2
BlinkerButton Button1(BUTTON_1);
BlinkerButton Button2(BUTTON_2);
void button1_callback(const String & state)
{
digitalWrite(LED_BUILTIN1, !digitalRead(LED_BUILTIN1));
BLINKER_LOG("get button state: ", state);
if (state == BLINKER_CMD_BUTTON_TAP) {
BLINKER_LOG("Button tap!");
Button1.print();
}
}
void button2_callback(const String & state)
{
digitalWrite(LED_BUILTIN2, !digitalRead(LED_BUILTIN2));
digitalWrite(LED_BUILTIN2, HIGH);
delay(400);
digitalWrite(LED_BUILTIN2, LOW);
BLINKER_LOG("Button tap!");
Button2.print();
}
void dataRead(const String & data)
{
BLINKER_LOG("Blinker readString: ", data);
Blinker.vibrate();
uint32_t BlinkerTime = millis();
Blinker.print("millis", BlinkerTime);
}
AHT20 humiditySensor;
Adafruit_BMP280 bmp;
Adafruit_Sensor *bmp_temp = bmp.getTemperatureSensor();
Adafruit_Sensor *bmp_pressure = bmp.getPressureSensor();
char auth[] = "09a0cd4b4016";
char ssid[] = "Atour";
char pswd[] = "4000606606";
BlinkerNumber Number1("num-abc");
BlinkerNumber Number2("num-abd");
BlinkerNumber Number3("num-abe");
BlinkerNumber Number4("num-abf");
BlinkerNumber Number5("num-abg");
BlinkerNumber Number6("num-abh");
BlinkerNumber Number7("num-abi");
BlinkerNumber Number8("num-abj");
volatile int light5;
volatile int light6;
volatile int light7;
volatile int light8;
void dataStorage(){
Blinker.dataStorage("num-abg", light5);
Blinker.dataStorage("num-abh", light6);
Blinker.dataStorage("num-abi", light7);
Blinker.dataStorage("num-abj", light8);
}
const int potPin5 = 32;
const int potPin6 = 33;
const int potPin7 = 34;
const int potPin8 = 35;
int potValue5 = 0;
int potValue6 = 0;
int potValue7 = 0;
int potValue8 = 0;
void setup() {
Blinker.begin(auth,ssid,pswd);
Serial.begin(115200);
unsigned status;
Wire.begin();
status = bmp.begin();
BLINKER_DEBUG.stream(Serial);
pinMode(LED_BUILTIN1, OUTPUT);
digitalWrite(LED_BUILTIN1, LOW);
pinMode(LED_BUILTIN2, OUTPUT);
digitalWrite(LED_BUILTIN2, LOW);
Blinker.attachData(dataRead);
Button1.attach(button1_callback);
Button2.attach(button2_callback);
if (humiditySensor.begin() == false)
{
Serial.println("AHT20 not detected. Please check wiring. Freezing.");
while (1);
}
Serial.println("AHT20 acknowledged.");
}
void loop() {
sensors_event_t temp_event, pressure_event;
bmp_temp->getEvent(&temp_event);
bmp_pressure->getEvent(&pressure_event);
if (humiditySensor.available() == true)
{
float temperature = humiditySensor.getTemperature();
float humidity = humiditySensor.getHumidity();
Serial.print("Temperature: ");
Serial.print(temp_event.temperature);
Serial.println(" C\t");
Serial.print("Pressure：");
Serial.print(pressure_event.pressure);
Serial.println(" hPa");
Serial.print("Temperature: ");
Serial.print(temperature, 2);
Serial.print(" C\t");
Serial.print("Humidity: ");
Serial.print(humidity, 2);
Serial.print("% RH");
Serial.println();
delay(100);
potValue5 = analogRead(potPin5);
potValue6 = analogRead(potPin6);
potValue7 = analogRead(potPin7);
potValue8 = analogRead(potPin8);
light5 = potValue5;
light6 = potValue6;
light7 = potValue7;
light8 = potValue8;
Number1.print(temp_event.temperature);
Number2.print(pressure_event.pressure);
Number3.print(humiditySensor.getTemperature());
Number4.print(humiditySensor.getHumidity());
Number5.print(light5);
Number6.print(light6);
Number7.print(light7);
Number8.print(light8);
Blinker.run();
}
delay(500);
}
esp32程序arduino程序
页:
[1]